How much stabilizer to add to a pool
Stabilizer, also sold as conditioner, is cyanuric acid (CYA). It shields chlorine from sunlight; HTH says it prevents up to 90% of the chlorine loss that sunlight causes. The dose depends on your pool's volume, how far you want to raise CYA, and the product. One ppm is one part in a million by weight, and a gallon of water weighs 8.345 lb, so for granules:
Pounds of granules = gallons × ppm to raise × 8.345 ÷ 1,000,000 ÷ purity
Grams of granules = liters × ppm to raise ÷ 1,000 ÷ purity
Purity is the cyanuric acid share on the label as a decimal (1 for 100%). Liquid stabilizer is a ready-to-pour product whose labels give its strength as a rate instead, usually "1 gallon raises 10,000 gallons by 32 ppm":
Gallons of liquid = ppm to raise ÷ label rate × gallons of pool ÷ 10,000
Example: a 15,000-gallon pool with no stabilizer, raised to 40 ppm, needs 15,000 × 40 × 8.345 ÷ 1,000,000 = 5.0 lb of granules, about 11 cups. With liquid at 32 ppm per gallon it is 40 ÷ 32 × 1.5 = 1.9 gallons.
Stabilizer per 10,000 gallons
| Raise CYA by | Granules, 100% | By volume | Liquid, 32 ppm per gallon |
|---|---|---|---|
| 1 ppm | 1.3 oz | 0.2 cup | 4 fl oz |
| 10 ppm | 13.4 oz (0.83 lb) | 1.9 cups | 40 fl oz (0.31 gal) |
| 20 ppm | 1.67 lb | 3.8 cups | 80 fl oz (0.63 gal) |
| 30 ppm | 2.50 lb | 5.6 cups | 0.94 gal |
| 40 ppm | 3.34 lb | 7.5 cups | 1.25 gal |
Granules are by weight; the cup figures use the "1 lb equals 2¼ cups" printed on stabilizer labels, and a kitchen scale is more accurate. The liquid column uses the rate on Natural Chemistry, Doheny's and HammerTech labels (4 fl oz per ppm per 10,000 gallons).
What "1 pound per 10,000 gallons" really gives
By the arithmetic above, 1 lb of pure cyanuric acid raises 10,000 gallons by about 12 ppm. Labels round differently: Pool Solutions' label says 2.5 lb raises 10,000 gallons by 30 ppm (12 per lb), Robelle's works out to about 12.5 to 13, and HTH and Puri Tech say 10 ppm per lb, which understates the rise, so following it lands about 20% above the level you aimed for. The calculator works from the chemistry, so it can come out a little lower than a label that uses the 10 ppm rule.
The right CYA level for your pool
| Pool | Trouble Free Pool | Makers' directions | Calculator's target |
|---|---|---|---|
| Outdoor, chlorine (liquid, tablets, cal-hypo) | 30 to 60 ppm | 30 to 50 (HTH, Orenda) | 40 |
| Outdoor, salt chlorine generator | 60 to 90 ppm | 60 to 80 (Hayward, HTH) | 70 |
| Indoor | 0 to 20 ppm | 0 (Hayward) | none added |
Salt pools run higher because a generator makes chlorine slowly, a little at a time, so it needs more protection. Public pools are different: CDC's Model Aquatic Health Code, a model code some states adopt, keeps CYA at or below 90 ppm.
More CYA is not better. Stabilizer holds part of the chlorine in reserve, so the higher your CYA, the more free chlorine (FC) you need for the same cleaning power. A common rule (Orenda, Trouble Free Pool) keeps FC at about 7.5% of CYA or more. That is why the calculator also shows the chlorine to keep for your new level:
| CYA | Free chlorine, minimum | Free chlorine, target |
|---|---|---|
| 30 | 2 | 4 to 6 |
| 40 | 3 | 5 to 7 |
| 50 | 4 | 6 to 8 |
| 60 | 5 | 7 to 9 |
| 70 | 5 | 8 to 10 |
| 80 | 6 | 9 to 11 |
| 90 | 7 | 10 to 12 |
Trouble Free Pool chart for pools without a salt generator; salt pools can run a little lower (see the chlorine calculator).
Granules or liquid?
Granular stabilizer is nearly pure cyanuric acid and the cheaper way to raise CYA, but it dissolves slowly (days) and is acidic, so it should not sit on a liner or plaster, and a big dose can nudge pH and alkalinity down. Liquid stabilizer is ready to pour (shake it first), shows up on a test by the next day and is easy to pour, but each jug raises CYA less, so it costs more for the same rise. Both do the same job once they are in the water.
How to add granular stabilizer
- Pour the measured granules into a sock: a skimmer sock, a clean tube sock or pantyhose.
- Set the sock in the skimmer basket, or hang it in front of a return jet. Squeeze it now and then to help it dissolve.
- Run the pump for 24 hours, and do not backwash or clean the filter for a week, so granules caught in the filter are not thrown away.
- Chlorinate as if all of it has already dissolved, at the level for your new CYA.
- Test CYA a day after the sock is empty. Do not add more before then.
Labels differ: HTH says to add stabilizer slowly through the skimmer, and some say to broadcast it over the pool. Follow yours. Through the skimmer, granules can sit in the filter for a week or more and are lost if you backwash early; broadcast, brush until no granules are left on the floor.
Why your CYA test is not going up
This is the most common stabilizer question, and the usual answer is patience. Granules can take two or three days to leave a sock and longer in a filter, and the test only counts what has dissolved. Adding more because the number has not moved is how pools end up over 100 ppm, and then the only fix is draining. Other causes:
- The test cannot read that low. Many drop-kit CYA tests cannot read below about 30 ppm, so the first 30 ppm you add may not show at all.
- Test strips. They are rough for CYA. A drop kit or a second test at a pool store is worth it before buying more.
- Technique. The CYA test is read by eye, so the light and the person reading it change the result. Test in good light with the sample near room temperature.
- The product. Check the label is cyanuric acid, and how much of it.
If the reading is above the top of the scale (100 ppm on most kits), Taylor's method is to mix one part pool water with one part tap water, test that, and double the result.
How to lower CYA
CYA does not evaporate and is not used up quickly, so in practice it leaves only with the water. Replace part of the water with fresh water, which has no CYA:
Share of water to replace = (current CYA − target) ÷ (current CYA − CYA in the fill water)
Example: 90 ppm down to 40 ppm needs (90 − 40) ÷ 90 = 56% of the water. In a 15,000-gallon pool that is 8,333 gallons. If you cannot drain that much at once, do it in rounds: two rounds of 33% (5,000 gallons each, 10,000 in total) or three rounds of 24% (3,553 each, 10,659 in total). Rounds are gentler but use more water, because each refill dilutes water that has already been diluted.
- Vinyl liners shrink without the water's weight. Never drain one empty, and keep at least a foot of water in the shallow end.
- In-ground pools can be pushed up out of the ground when the ground water is high, and above-ground pools need the water to support the walls. Ask your builder before draining low.
- Stop the source. Chlorine tablets (trichlor) add about 6 ppm of CYA for every 10 ppm of chlorine, and dichlor about 9. Switch to liquid chlorine, cal-hypo or a salt generator until CYA is down.
- Salt pools lose salt in the same share, so re-check it with the salt calculator.
Where water is scarce or expensive, mobile reverse-osmosis services can filter CYA out without draining. Bacterial "CYA reducer" products exist, but they need warm water with no chlorine for days, and results vary widely.
Frequently asked questions
Is pool conditioner the same as stabilizer?
Yes. Stabilizer, conditioner, cyanuric acid and CYA all mean the same chemical. "Stabilized chlorine" is something else: tablets (trichlor) and dichlor granules are chlorine with CYA built in, so they raise CYA as a side effect.
How soon can I swim after adding stabilizer?
Follow the label on your product; it sets the re-entry time. Wait until no granules are left on the floor, and keep chlorine at the right level for the new CYA while it dissolves.
Does a salt water pool need stabilizer?
Yes, if it is outdoors. Generator makers such as Hayward ask for 60 to 80 ppm, higher than a chlorine pool, because the generator makes chlorine slowly and sunlight would burn it off as fast as it is made.
Does an indoor pool need stabilizer?
Usually not. Without sunlight there is nothing to protect chlorine from, and CYA only makes chlorine slower to work. Trouble Free Pool allows 0 to 20 ppm indoors, and Hayward says 0.
Is high CYA "chlorine lock"?
No. Chlorine still works with high CYA; you just need more of it, in proportion. At 90 ppm CYA the minimum is about 7 ppm of free chlorine, which is hard and expensive to hold, so most owners lower CYA instead. Above 100 ppm the chlorine chart stops.
Why does CYA go down on its own?
Through water loss: splash-out, backwashing, rain that overflows the pool, draining and leaks. Hayward's manual notes that CYA and salt usually fall together for that reason. Test CYA every month or so, and after big refills.
Sources
- Target ranges, sock method, pump and filter, testing the day after it dissolves, lowering by water replacement and reverse osmosis: Trouble Free Pool, ABCs of pool water chemistry. Free chlorine by CYA: Trouble Free Pool chlorine/CYA chart
- Makers' ranges: HTH Chlorine Stabilizer (30 to 50, salt 60 to 80, 1 lb per 10,000 gallons for 10 ppm, add through the skimmer, up to 90% less chlorine loss, re-test pH and alkalinity); Orenda, ideal CYA level (30 to 50 for home pools, free chlorine about 7.5% of CYA); Hayward Salt & Swim manual (60 to 80 outdoors, 0 indoors); Hayward AquaTrol manual (CYA and salt fall together)
- Public pools at or below 90 ppm: CDC 2024 MAHC inspection cheat sheet
- Granular labels (2.5 lb per 10,000 gallons for 30 ppm, 1 lb = 2¼ cups): Pool Solutions stabilizer; Doc stabilizer; Robelle; Puri Tech
- Liquid labels (1 gallon raises 10,000 gallons by 32 ppm): Natural Chemistry Instant Pool Water Conditioner; Doheny's Quick Stabilizer; HammerTech. Liquid shows on the test the next day: Trouble Free Pool forum
- Diluting a CYA test above 100 ppm: Taylor Technologies. Kits that cannot read below 30 ppm: Trouble Free Pool forum, Taylor K-2006
- Lowering CYA, reverse osmosis and bacterial reducers: Orenda; Montana DPHHS, cyanuric acid (partial drain; trichlor is 54% cyanuric acid by weight, and with 90% available chlorine that is 6 ppm of CYA per 10 ppm of chlorine). Dichlor, 9 ppm per 10: AQUA Magazine; both also follow from the molar masses
- Draining vinyl and in-ground pools: Trouble Free Pool forum (a foot of water in the shallow end); Pool Solutions (liners and ground water); Royal Swimming Pools (above-ground walls)
Last checked November 23, 2026. Always follow the label on your stabilizer.
Related calculators
- Pool Volume CalculatorHow many gallons your pool holds. Any shape, sloped or hopper floors, above-ground pools.
- Pool Salt CalculatorHow much salt to add, in pounds and bags, for your generator's target. Too high? How much water to replace.
- Pool Chlorine CalculatorHow much liquid chlorine, bleach or granules to add, with a target set by your stabilizer (CYA) level.
- Pool Shock CalculatorHow many bags of shock or jugs of liquid chlorine, for a routine shock or to clear algae at the level your CYA needs.
- Pool Alkalinity CalculatorHow much baking soda raises total alkalinity, or how much acid lowers it, in safe rounds.