How much salt to add to a pool
You need three numbers: how many gallons the pool holds, the salt reading now, and the target for your generator. The salt to add is the difference in ppm (parts per million), scaled up to your pool:
Pounds of salt = gallons × (target ppm − current ppm) × 8.345 ÷ 1,000,000
Kilograms of salt = liters × (target ppm − current ppm) ÷ 1,000,000
The 8.345 is the weight of a gallon of water in pounds, so one ppm in one gallon weighs 8.345 millionths of a pound. Example: a 15,000-gallon pool with no salt, aiming for 3,200 ppm, needs 15,000 × 3,200 × 8.345 ÷ 1,000,000 = 400.6 lb, which is 10 bags of 40 lb. This matches the makers' own charts: Hayward lists 267 lb for 10,000 gallons going from 0 to 3,200 ppm.
Pounds of salt to reach 3,200 ppm
| Pool size | From 0 ppm | From 1,500 | From 2,500 | From 3,000 |
|---|---|---|---|---|
| 10,000 gal | 267 lb | 142 lb | 58 lb | 17 lb |
| 15,000 gal | 401 lb | 213 lb | 88 lb | 25 lb |
| 20,000 gal | 534 lb | 284 lb | 117 lb | 33 lb |
| 25,000 gal | 668 lb | 355 lb | 146 lb | 42 lb |
| 30,000 gal | 801 lb | 426 lb | 175 lb | 50 lb |
Divide by 40 for the number of 40 lb bags. If your generator's target is not 3,200 ppm, use the calculator above.
Salt level by generator
There is no single right salt level. Each salt chlorine generator is built for its own range, and running outside it can stop chlorine production or wear the cell. The calculator uses the target from the maker's manual:
| Generator | Range in the manual | Target we use |
|---|---|---|
| Hayward AquaRite, AquaTrol, Salt & Swim | 2,700–3,400 ppm | 3,200 (Hayward's optimum) |
| Hayward AquaTrol low-salt (RJLS) | 1,200–1,800 ppm | 1,500 (Hayward's optimum) |
| Pentair IntelliChlor IC20, IC40, IC60 | 3,000–3,500 ppm | 3,400 (Pentair's salt charts aim here) |
| Pentair IntelliChlor Plus, LT | at least 3,000 ppm | 3,600 (Pentair's stated ideal) |
| Jandy AquaPure, PureLink | 3,000–3,500 ppm | 3,200 (inside the range) |
| Jandy AquaPure Ei | 4,000–4,500 ppm | 4,000 |
| CircuPool RJ series | 3,000–4,000 ppm | 3,500 (CircuPool's ideal) |
| Intex Krystal Clear saltwater | 2,500–3,500 ppm | 3,000 (Intex's optimum) |
Manuals change between model years, so if yours gives a different number, choose Custom target and enter it. Hayward's AquaRite 100 is an exception worth knowing: on pools up to 15,000 gallons it can run on lower salt, from 1,500 to 2,700 ppm.
How to add salt to your pool
- Test first. Use salt test strips or a drop kit. A pool that has been chlorinated for years often has some salt already. Pentair notes that its generator's own salt reading can be up to 500 ppm off, so check before buying a large amount.
- Buy the right salt. Plain sodium chloride, at least 99% pure (Pentair and Intex ask for 99.8%; check the bag and your manual), sold as pool salt or coarse solar salt. Plain water-softener pellets with no additives work too but dissolve slowly. Avoid rock salt, iodized salt and salt with anti-caking additives or yellow prussiate of soda.
- New plaster? Hayward says to wait 10 to 14 days after plastering before adding salt. Ask your builder too.
- Add about three-quarters first. With the pump running, pour the salt into the pool itself, not the skimmer, and brush it so it does not sit in a pile. Many manuals, including Intex's, CircuPool's and Pentair's, say to keep the generator switched off until the salt has dissolved.
- Run the pump about 24 hours, then test again and add the rest if the reading is still low.
Salt too high? Lower it with fresh water
First, re-test. A reading a little above the range is common, testers disagree by a few hundred ppm, and salt drifts down on its own with splash-out and backwashing. The calculator suggests replacing water only from the maker's own "dilute" level where one is published (Hayward's salt chart: 3,600 ppm; Pentair IntelliChlor: above 4,200 ppm), and otherwise from 500 ppm above the manual's range.
Salt does not evaporate, and no chemical takes it out. The only way down is to replace some of the water. The share to replace is:
Share of water to replace = (current ppm − target ppm) ÷ (current ppm − fill water ppm)
Example: a 15,000-gallon pool at 4,200 ppm, target 3,200, refilled with salt-free water: (4,200 − 3,200) ÷ 4,200 = 0.238, so about 3,570 gallons. Doing it in several smaller rounds is gentler on the pool but uses a little more water. If your tap water has some salt, enter it under Salt in your fill water; it raises the amount to replace.
Why the salt did not rise as expected
If you added the calculated amount and the reading came out far higher or lower, the usual cause is the pool volume. A 20% error in gallons is a 20% error in salt. Turn it around and use the salt to measure the pool: enter the pounds you added and the readings before and after in the salt check on the pool volume calculator. Other causes are salt that has not fully dissolved yet and testers that disagree with each other, so compare readings from the same tester.
Pool salt questions
How many bags of salt for a 15,000-gallon pool?
From no salt to 3,200 ppm, about 400 lb, or 10 bags of 40 lb. For a top-up, enter your current reading above; going from 2,500 to 3,200 ppm takes about 88 lb.
Does pool salt get used up?
No. The generator turns salt into chlorine, and the chlorine turns back into salt. It leaves only with water: splash-out, backwashing, draining and rain that overflows the pool. Evaporation leaves the salt behind.
Will the pool taste salty?
Hayward says most people start to taste salt at about 3,500 to 4,000 ppm. For comparison, CircuPool notes that sea water is around 35,000 ppm, ten times more.
Can I use table salt?
Not iodized table salt or salt with anti-caking agents, which can stain. Plain salt that is at least 99% sodium chloride, with no additives, is fine; some makers ask for 99.8%.
Sources
- Pounds = gallons × 8.34 × ppm ÷ 1,000,000 (we use 8.345, the same figure to one more decimal place): Florida DEP water treatment formula sheet. The same ratio in a salt chart (267 lb for 10,000 gal, 0 to 3,200 ppm), Hayward's 2,700–3,400 ppm range with 3,200 optimal, and taste at 3,500–4,000 ppm: Hayward, How much salt do you add
- Hayward salt type, adding salt, 24 hours of pumping, new plaster 10–14 days: Hayward chemistry quick start guide and Hayward AquaRite owner's manual; lower salt on AquaRite 100: AquaRite 100 owner's manual; AquaTrol 2,700–3,400 ppm: AquaTrol owner's manual; Salt & Swim: Salt & Swim manual; AquaTrol low-salt 1,200–1,800 ppm, 1,500 optimal: AquaTrol RJLS manual; salt chart marking 3,600 ppm "dilute": Hayward salt chlorination training guide
- Pentair IntelliChlor 3,000–3,500 ppm and the ±500 ppm sensor: IntelliChlor installation and user's guide; salt chart to 3,400 ppm and 3,000–4,200 ppm working range: IntelliChlor IC20/IC40 guide. IntelliChlor Plus and LT, 3,600 ppm ideal: Pentair
- Jandy AquaPure 3.0–3.5 g/L (3,000–3,500 ppm): AquaPure and PureLink manual; AquaPure Ei 4,000–4,500 ppm: AquaPure Ei manual
- CircuPool RJ 3,000–4,000 ppm, ideal 3,500, and sea water at about 35,000 ppm: CircuPool RJ guide and RJ+ owner's manual
- Intex 2,500–3,500 ppm, 3,000 optimal, generator off while salt dissolves: Intex QS200 manual and Intex CS3110 manual
Last checked November 22, 2026. Always follow your generator's manual and the label on the salt bag.